December 18

Time to give your sprayer some TLC

first_imgShare Facebook Twitter Google + LinkedIn Pinterest It is very likely that you will not be using your sprayer again until next spring. If you want to avoid potential problems and save yourself from frustration and major headaches, you will be wise to give your sprayer a little bit of TLC (Tender Loving Care) these days. Yes this is still a busy time of the year for some of you, but don’t delay winterizing your sprayer any more than necessary. Find ways to protect them against the harmful effects of snow, rain, sun, and strong winds. Moisture in the air, whether from snow, rain, or soil, rusts metal parts of unpro­tected equipment of any kind. This is especially true for a sprayer, because there are all kinds of hoses, rubber gaskets and plastic pieces all around a sprayer. Yes, the sun usually helps reduce moisture in the air, but it also causes damage. Ultraviolet light softens and weakens rubber materials such as hoses and tires and degrades some tank materials. How about the pump, the heart of a sprayer? You don’t want a pump that is cracked and/or not working at its full capacity because you did not properly winterize it before the temperature falls below freezing.The best protection from the environment is to store sprayers in a dry building. Storing sprayers in a building gives you a chance to work on them any time during the off-season regardless of weather. If storing in a building is not possible, provide some sort of cover.Here are some suggestions you may want to follow as you prepare the sprayer for storage: When storing trailer-type sprayers, put blocks under the frame or axle and reduce tire pressure during storage.It is very likely that you did the right thing when you used the sprayer the last time: you rinsed the whole system (tanks, hoses, filters, nozzles) thoroughly. If you did not, make sure there is no leftover spray mixture in the tank. Dispose of it according to the chemical label, and rinse the system with some sort of a rinsing solution. Usually a mixture of one to 100 of household ammonia to water should be adequate for cleaning the tank, but you may first need to clean the tank with a mixture containing detergent if tank was not cleaned weeks ago, right after the last spraying job was done.Cleaning the outside of the sprayer components deserves equal attention. Remove compacted deposits with a bristle brush. Then flush the exterior parts of the equipment with water. A high pressure washer can be used, if avail­able. Wash the exterior of the equipment either in the field away from ditches and water sources nearby, or a specially constructed concrete rinse pad.Drain all cleaning water from all parts to prevent freezing.To prevent corrosion, remove nozzle tips and strainers, dry them, and store them in a dry place. Putting them in a can of light oil such as diesel fuel or kerosene is another option.Pumps require special care. After draining the water, add a small amount of oil, and rotate the pump four or five revolutions by hand to completely coat interior surfaces.  Make sure that this oil is not going to damage rubber rollers in a roller pump or rubber parts in a diaphragm pump. Check the operator’s manual. If oil is not recom­mended, pouring one tablespoon of radiator rust inhibitor in the inlet and outlet part of the pump also keeps the pump from corroding. Another alternative is to put automotive antifreeze with rust inhibitor in the pump and other sprayer parts. This also protects against corrosion and prevents freezing in case all the water is not drained.Cover openings so that insects, dirt, and other foreign material cannot get into the system.Finally, check the sprayer for scratched spots. Touch up these areas with paint to eliminate corrosion. Erdal Ozkan, Professor and Extension Agricultural engineer, can be reached at 614-292-3006, or [email protected] This column is provided by the OSU Department of Food, Agricultural and Biological Engineering, OSU Extension, Ohio Agricultural Research & Development Center, and the College of Food, Agricultural and Environmental Sciences.last_img read more

December 12

Community Capacity Building: Say what??

first_imgThe MFLN consists of several concentration areas including Community Capacity Building (CCB). But many people wonder…what is CCB? What do those words even mean? Our FDEI team began to explore this idea through the lens of early childhood special education (ECSE) and early intervention (EI), and we discovered not only what the term means, but also how it can be used as a force multiplier for young children and their families in the Family Readiness mission.CCB is often defined as “people who feel a sense of shared responsibility and apply their strengths to achieve desired results” (Mancini & Bowen, 2014). Ultimately the goal of CCB is for both informal and formal support systems to work together to achieve positive result for members of the community.In the field of EI/ECSE, the desired result of our community (professionals and families who work together on behalf of young children with disabilities) is to see children learn and grow to their full potential through nurturing, enriched relationships with caregivers.  The informal supports within this community are parents, caregivers, extended family, friends, and other individuals who interact with the child in relatively intimate relationships. Formal supports include YOU – the EI/ECSE professional! This symbiotic relationship between informal and formal supports for children is a force multiplier that enhances outcomes for children. Like a rock thrown into a pond,CCB has a ripple effect that spreads wide and deep.As an ECSE/EI professional, you are in the position to equip caregivers with skills and knowledge to nurture a child’s growth and development. And FDEI is here to help you do just that. Community Capacity Building at its best: All of us using our strengths to achieve desired results. When one part of this formula is missing, the capacity of all decreases…so let’s work together to achieve remarkable outcomes.Created by R. DiPietro-Wells; Images from pixabay.com CC0How can we help support you? What kinds of information do you need to help support the military families you serve? What questions do you have? What resources do you need? We would love to hear from you. Feel free to comment below or email us at [email protected] can learn even more about CCB and access an online training to increase your understanding of CCB here.This post was edited by Robyn DiPietro-Wells & Michaelene Ostrosky, PhD, members of the MFLN FD Early Intervention team, which aims to support the development of professionals working with military families. Find out more about the Military Families Learning Network FD concentration on our website, on Facebook, on Twitter, YouTube, and on LinkedIn.last_img read more